• June 14, 2019

The LM series are precision easily-calibrated integrat- ed circuit temperature sensors Operating as a 2-terminal zener the LM has a breakdown voltage. lm are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for lm Data sheet, LM manual, LM pdf, LM, datenblatt, Electronics LM, alldatasheet, free, datasheet, Datasheets, data sheet, datas sheets, databook.

Author: Kazijas Goltisho
Country: Kuwait
Language: English (Spanish)
Genre: Health and Food
Published (Last): 4 November 2009
Pages: 72
PDF File Size: 16.53 Mb
ePub File Size: 5.7 Mb
ISBN: 885-3-78538-407-2
Downloads: 59575
Price: Free* [*Free Regsitration Required]
Uploader: Neran

The raw voltage over this value therefore represents the ratio of how much power the output pin is outputting against this full range.

The difference between an LM and LM34 and LM35 temperature sensors is the LM sensor gives out the temperature in degrees Kelvin, while the LM35 sensor gives out the temperature in degrees Celsius and the LM34 sensor gives out the temperature in degrees Fahrenheit.

You can adjust this value to meet your personal preference or program needs.

LM35 Temperature Sensor

Below is the pinout of the LM IC: The code is shown below. So to get the degree value in fahrenheit, all that must be done is to take the voltage output and divide it by this give out the datashert degrees in fahrenheit.

This translates into the circuit schematic: This allows us to calibrate the temperature sensor if we want a more precise dstasheet readout.

In this project, we will demonstrate how to build temperature sensor circuit using a LM sensor. This is the datasheet of the LM IC: The arduino, with suitable code, can then interpret this measured analog voltage and output to us the temperature in degrees Kelvin, Celsius, and Fahrenheit.


The arduino will then read this measured value from datadheet LM and translate into degrees kelvin, fahrenheit and celsius, which we will be able to read from the computer from the arduino serial monitor. We will integrate this with the arduino to measure the temperature.

All you have to do is take the output reading and divide it by 10 in order to get the temperature output reading. Since the output pin can give out a maximum of 5 voltsrepresents the full possible range it can satasheet out. We get the ratio of the raw value to the full span of and then multiply daatasheet by to get the millivolt value.

This is because there is millvolts in 5 volts.

LM Datasheet, PDF – Alldatasheet

Pin 3 is the ground pin and connects to the ground GND terminal of the arduino. This is ideal because the arduino’s power pin gives out 5V of power.

Pin 2 is the output pin. It is divided by because a span of occupies 5V. Once lm35 have this ratio, we then multiply it by to give the millivolt value. Now the computer is connected to the arduino. Before we can get a Kevlin reading of the temperature, the analog output voltage must first be read.

We can now write code in the processing software to give instructions to the arduino. This is so that we can hook our arduino to a computer and send it code that it can run to display to us the temperature. Pin 2 gives an output of 1 millivolt per 0. The output pin provides an analog voltage output that is linearly proportional to the fahrenheit temperature.


Pin 1 is the Adjustable Pin Adj.

LM Datasheet pdf – Precision Temperature Sensor – National Semiconductor

So, for example, if the output pin, pin 2, gives out a value of mV 0. Temperature Sensor Circuit The temperature sensor circuit we will build is shown below: Once this analog voltage in millivolts is calculated, we then can find the temperature in kelvin by the equation: So if the LM is giving an output reading of 2.

This output reading of So you circuit connections are: All 3 are calibrated different to output the millivolt voltage reading in proportional to these different units of measurement. Once we obtain this Celsius value, we can convert into Fahrenheit with the following equation: The type B side of the connector goes into the arduino and the type A side into the USB port of the computer.

We can use any type of arduino board. This will be the raw value divided by times As a temperature sensor, the circuit will read the temperature of the surrounding environment and relay this temperature to us back in degrees Kelvin. All we must do is write this code and upload it to the arduino to convert this kelvin temperature into fahrenheit and celsius.