FX1N HARDWARE MANUAL PDF

  • June 13, 2019

and wiring for Japanese specification FX1N PLC main units. This manual covers basic hardware details for the FX1N Series Programmable Logic Controller. FX1N Hardware Manual – 三菱可编程控制器FX1N型PLC硬件手册. User’s Manual. (Data Communication). FX1S/FX1N/FX2N(C)/FX3U. Interface Modules. INDUSTRIAL AUTOMATION. MITSUBISHI ELECTRIC. MITSUBISHI.

Author: Mukazahn Gut
Country: Bhutan
Language: English (Spanish)
Genre: Politics
Published (Last): 11 December 2016
Pages: 179
PDF File Size: 14.82 Mb
ePub File Size: 4.36 Mb
ISBN: 871-8-30050-801-1
Downloads: 1435
Price: Free* [*Free Regsitration Required]
Uploader: Dourn

FX1N Hardware Manual_图文_百度文库

Do not use this terminal Fuse Surge absorbing Diode. This manual provides information for the installation and use of the FX1N. A standard input X0 to X17 defined by the system parameters. Never mount them to the floor or ceiling of an enclosure. Terminals screws should be tightened to between 0. This includes being completely familiar with all associated documentation for the said product. Software warning 4 Indicates special care must be taken when using this element of software.

If resistance Rp is less than the stated value, then add Rb.

Do not remove this screw. The enclosure should be selected and installed in accordance to the local and national standards.

Check the output LEDs for operation. E C A Special function or optional equipment board.

Mitsubishi FX1N-24MT-DSS Manuals

Terminal layouts The following selection of terminal layouts are taken from the FX1N product range. For improved response times use a ‘dummy’ resistor, see the figure below. Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples.

  EVANGELIOS PARA SANAR ALEJANDRO JODOROWSKY PDF

Secure top cover with M3 screw E. Units should not be installed in areas subject to the following conditions: FX0N series extension units do not have UL certification. D, D M Program circuit error ref.

C M3 screw to secure top cover. During this testing stage take extreme care not to touch any live or manul parts.

E M3 screw to secure top cover. Features table 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Top cover Direct mounting holes 4. PL E xtension block? C M3 screw to secure board. The rated life for an inductive AC load such as a contactor or solenoid valve isoperations at 20VA.

See equation 1 for Rb calculation. All examples and diagrams shown in this manual are intended only as an aid to understanding the text, not to guarantee operation. D Top cover for board. Down load a small test program into the PLC. Note that the ground cable must not be connected to the same ground as the power circuits.

B Optional equipment connector port. Once installation is complete remove the protective paper band, to prevent overheating. Each of the symbols used will now be listed with a brief description of its meaning. Circuit protector or Fuse? Please refer to the table below. D, D M Program execution error ref. If in doubt at any stage of the installation of an FX1N Series Programmable Controller always consult a professional electrical engineer who is qualified and trained to the local and national standards which apply to the installation site.

  GIJOM MUSO ZATO STO TE VOLIM PDF

Please note that the over current induced by in-rush greatly reduces the relay contacts service life. Note all counters are latched Remarks C0 to C15 Type: Grounding is recommended but if a proper ground cannot be provided, the PLC will still operate correctly without being grounded. These engineers should be fully aware of all aspects of safety with regards to automated equipment. Whenever any of the following symbols are encountered, its associated note must be read and understood.

Input circuit power supply? Always make sure the power is turned off, before installing a special function board. All maintenance should be carried out in accordance with established safety practices.

Screw terminals must be secured to prevent a loose connection from causing a malfunction. However Additional extension blocks can be powered from the main unit power supply 4. Check D for program scan time, units 0. Remove the base unit top cover. Parallel LED Eqn 1: Only one board can be used at any one time, do not try to stack multiple boards.

Mitsubishi FX1N-24MT-ESS/UL Manuals

If a response time of 0. AC, World spec, CE registered. Check the power LED is lit.

Verify the program to ensure it has been written to the PLC correctly.