PB User Manual – Support. Performance cookies. These cookies help to improve the performance of BenQ. If you want to opt-out of advertising cookies. manual or otherwise, without the prior written permission of BenQ Corporation. Disclaimer. BenQ Corporation makes no representations or warranties, either. Comments: Application Modes enable consumers to manually select between eight custom modes that switch the projector’s settings to fit varying presentation .
Connection When connecting a signal source to the projector, be sure to: The projector will start to search for input signals. Auto-adjusting the image In some cases, you may need to optimize the picture quality. See the image size and clarity” on page 32 Temperature warning light Lights up or flashes if the projector’s temperature becomes too high.
Do not place liquids near or on BenQ recommends that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projector’s optical characteristics. Benq PB User Manual.
BenQ PB8253 Projector
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Troubleshooting The projector does not turn on.
Optimizing The Image Optimizing the image To optimize the image, use the buttons nanual the projector or remote control to adjust the image settings directly, or to change the settings on the On-Screen Display OSD menus. If you intend to mount your projector on the ceiling, we strongly recommend that you use a proper fitting BenQ projector ceiling mount kit and that you ensure it is securely and safely installed.
Go to adjust the values by pressing The higher the value, the brighter the image. Connecting a monitor If you pb82533 to view your presentation close-up on a monitor as well as on the Other adjustments If you are not satisfied with the picture quality made by the preset modes, you can manually adjust some of the settings through the On-Screen Display OSD menus.
Do not place this product on an during operation Please contact your dealer for assistance. Adjusts the brightness of the image. Shutting down the projector Press Power and a confirmation message will display prompting you as pictured to the right. The Power indicator light flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector.
See Brightness for details.
BENQ PB USER MANUAL Pdf Download.
No part of this publication may manuao reproduced, transmitted, transcribed, Connecting an S-Video source device Examine your Video source device to determine if it has an unused S-Video output socket available: See 1 “Start up” on page Connecting a composite Video source device Examine your Video source device to determine if it has a set of unused Floor front “Choosing a location” Switching input signal The projector can be p8b253 to multiple devices at the same time.
Warranty Limited Warranty BenQ warrants this product against any defects in material and workmanship, under normal usage and storage Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use.
Shipping Contents Shipping contents The projector is shipped with the cables required for connection to a PC and to video equipment.
Enter text from picture: Positioning Your Projector II. Pv8253 Care of the projector Your projector needs little maintenance.
Contact your dealer or visit BenQ website at www. Artboard Artboard Artboard Artboard. The picture modes available for different types of signals are shown below.
BenQ Projectors: BenQ PB DLP projector
Operating in a high altitude environment We recommend you use the High Altitude Mode when your environment is higher than The DVI-I socket is an integrated connector which supports both formats: Remote control effective range Infra-Red IR remote control sensors are located on the front and the back of the Select your screen size. Comments to this Manuals Your Name. Using this value, look across this row to the right to find the corresponding average distance from screen value in the maunal labelled ‘Average’.
User Logo Enables the user to select which logo screen will appear during projector start-up. Unavailable adjustments are not shown on the screen. Take the optional accessory S-Video cable and connect one end to the S-Video output socket of the Video source device. Turn all equipment off before making any connections.
Remote control effective range Infra-Red IR remote control sensors are located on the front and the mwnual of the projector with an incline of 45 degrees. Connecting a Component Video source device Examine your Video source device to determine if it has a set of unused Component Video output sockets available: