9MM BSP SUBMACHINE GUN PDF

  • June 13, 2019

The following design drawings illustrate the construction of a 9mm submachine gun utilizing off the shelf ‘British Standard Pipe’ (BSP) Fittings. This post accompanies the seventeenth in a series of collaborative videos produced with ARES Researcher Ian McCollum, who also runs the. Possibly homemade, the submachine-gun and five sawed-off bsp 9mm of lutys sight free plans for all jump.

Author: Yozshular Nakinos
Country: Denmark
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 9 September 2007
Pages: 31
PDF File Size: 10.66 Mb
ePub File Size: 17.60 Mb
ISBN: 527-9-91437-617-2
Downloads: 69968
Price: Free* [*Free Regsitration Required]
Uploader: Matilar

As much as I support gun rights, your penultimate sentence is a load of crap. Each video will be accompanied by a blog post, here on The Hoplite, and supported by high quality reference photographs.

9mm BSP Machine Gun – Replica Plans and Blueprints

Further, the manufacturer must also obtain quantities of suitable ammunition. It is indeed a home manufactured submachine gun. Aden, Thanks for the kind words!

The end of the bolt section being fitted bs the firing pin prior to this. It must be ensured before welding that the top edge of the well is 7mm above the top edge of the receiver. Side lever grease applicator and internai spring. The following pages illustrate how this is done. The SMG shown may be a re-activated firearm that was imported as de-activated and therefore beyond the scope of our firearms laws from some ancient surplus lot. See book for detaiis. Even the vertical mag models that were submachnie and the German MP that copied them.

Two studding connectors are used to hold the side – plates together Expedient Homemade Firearms. The lower receiver template is attached to a section of 2. Just got here from Forgotten Weapons link. The gnu connectors must be exactly 20mm in length. The assembly is then thoroughly tightened.

9mm BSP Machine Gun – Replica Plans and Blueprints – PDF Drive

A 4mm diameter dowel pin is tapped into the sears 3. Erik, interesting, I dismissed the sten because of the magazine. I think they look very much alike, but there are a few noticeable differences.

  BEYOND THE LINES KULDIP NAYAR PDF

If the builder is a machinist with a lathe and mill, the job will take no more then two days. The selector switch is rotated either clockwise or anti-clockwise to allow the stock to be extended or closed; in just the same manner as if undoing a nut or bolt! All homemade, no powder burners but pneumatic and gas powered, all homemade and some remarkable examples in the showcase section. The trick nowadays would be finding the barrel and to a lesser degree magazine. I retired as Editor in Chief in Can anyone here identify it?

This pin shouid be 20mm in iength.

BSP mm SMG – BSP 9mm SMG – Bev Fitchett’s Guns Magazine

If you do not have specialist knowledge, never assume that arms or munitions are safe to handle until they have been inspected by a subject matter specialist.

It spent a hour looking for this gun. About two weeks ago the police in Winnipeg, Canada, confiscated a a bunch of saw off shotguns, ammo and a unidentified submachine gun that is reported to be homemade.

Using access to unique collections facilitated by ARES, this series of videos will examine a range of interesting weapons over the coming months.

The magazine and magazine well being two examples. If a firearm could be manufactured entirely from scratch using commonly available materials, then anyone with the requisite skill would be able to bypass national or local firearms law and restrictions on sale.

The most expensive part is the cheap barrel.

This spring is aimost perfect in dimensions for the BSP machine submacgine and was removed from the grease gun shown below. I will leave the reader to decide whether this design is good, bad, or somewhere in between! Cutting down the stock makes it too short and therefore illegal. During my decade at TFB I was fortunate to work with the most amazing talented writers and genuinely good people! Blowback sub-machine guns may be simple and cheap to produce, but they are highly sensitive to internal geometry and details of magazine design in particular.

  EUROMODELISMO 109 PDF

It sounds nutso in this day and age. Additional information is always welcome. At one time, the plans were available from Paladin Press pretty sure. Possibly due to it being handmade and homemade. It is very important that the submcahine edge of the grip is positioned 2. The following design drawings illustrate the construction of a 9mm submachine gun utilizing off the shelf ‘British Standard Pipe’ BSP Fittings.

Remember, all arms and munitions are dangerous. LutySALWsub-machine gun. Four dome head cap screws are then screwed into the connectors and thoroughiy tightened, effectively holding the assembiy together. Responses brandon How to make homemade gun designer?

The weapon is a 9 mm automatic, built from the book Expedient Homemade Firearms. You can find the how-to guide on scribd, at http: I too thought it looked a lot like an old MP from the WW2 era. The following design is offered on the understanding that the reader is already familiar with the firearm construction methods shown in my previous ‘Expedient Homemade Firearms’ books.

Canadian firearms law re: Neat looking machine gun though, looks like an M16A1 style pistol grip. The important difference arguments over the control of information notwithstanding is that it was quite legal under US Federal and local law for DD to manufacture and test-fire their prototypes.